Ridgid 535 Threader

Ridgid 535 Threader

• Pipe Capacity: 1/8" - 2" (3 mm - 50 mm) 2 ¼" - 4" (62 mm - 100 mm), 4" - 6" (100 mm - 150 mm) with 141 and 161 Geared Threaders
• Bolt Capacity: ¼" -2" (6 mm -50 mm)
• Motor: ½ HP, single-phase, 115V, 25-60 Hz, 15 Amp Reversible Universal motor.
• Switches: FOR/OFF/REV and Integral Safety Foot Switch
• Chuck: Speed Chuck™ with replaceable rocker-action jaw inserts (3)
• Rear Centering Device: Cam-action, turns with chuck
• Cutters: Self-centering, full-floating. Standard. No. 820 Wheel-Type Cutter, pipe capacity 1/8" - 2" (3mm-50mm), bolt capacity ¼" - 1" (6mm-25mm).
• Spindle Speed: 36 RPM standard (no load), 54 RPM model also available
• Reamer: 5-flute cone, RH, 1/8 "- 2" (3 mm - 50 mm)
• Oil Pump: Self-priming gerotor oil pump.

Ridgid 1224 Threader

Ridgid 1224 Threader

• Threads ¼"-2" pipe at 36 RPM and 2½"-4" at 12 RPM.
• The 1224 threads a wide range of pipe including black, galvanized and plastic-coated pipe, together with stainless steel, IMC and heavy-wall conduit, as well as rod up to 30 Rockwell C.
• An induction motor helps insure sound levels well within the limits set by the regulating authorities.
• A special capacitor-start/capacitor-run motor allows the 1224 to thread a full range of material where voltage drop is experienced.
• ¼"-2" Universal Die Head; 2½"-4" receding die head allows cutting of tapered or straight NPT/NPSM or BSPT/BSPP threads.
• Constant and proper lubrication of dies and workpiece with through-head oiling.

Wheeler Rex 6590 Threader

Wheeler Rex 6590 Threader

This machine has self opening notch type die heads with through die head oiling. These die heads offer accuracy and quick changes between pipe sizes, while providing quality threads. The 6590 is totally gear driven and powered by a condenser motor, producing extremely low noise levels. Quiet operation permits use in hospitals, factories, and in other locations where noise can be a problem. Completely equipped to cut, thread, and ream.

• For 2 ½" to 6" pipe
• 110/120 V. 75KW condenser motor, average noise level: 76db, maximum amperage under load: 14.5, no load RPM: 6.½0.2

Wheeler Rex 7090 Threader

Wheeler Rex 7090 Threader

Features complete interchangeability with the Model 300 dies and die heads. This portable and compact, high-performance threading machine has a self-opening die head and through the die head oiling. Completely equipped to cut, thread and ream.

• For ½" to 2" pipe
• 110/120 V, Single phase 600W series motor, average noise level: 84db, maximum amperage under load: 18.5, no load RPM: 41

Ridgid 258 Power Pipe Cutter

Ridgid 258 Power Pipe Cutter

The RIDGID Model 258 Power Pipe Cutter cuts 2½" to 8" schedule 10*/40 steel pipe, galvanized pipe, rigid conduit etc. at the job-site or inthe shop. Powered by the RIDGID No. 700 Power Drive, the 258 is a displacement cutter that provides square cuts. The operator controls the feeding rate by pumping the hydraulic foot pump throughout the operation. A square cut with minimal burr on either 21' or nipple lengths of pipe is safely achieved in seconds without abrasive dust, sparks, or open flame.

• Square cut 21' or nipple lengths of pipe without effort
• Easily cuts by displacing instead of removing pipe material
• No abrasive dust, dangerous sparks, or open flame
• Quickly cuts steel pipe with minimal burr
• Great for cutting pipe for groove joining
• Heavy-Duty design is perfect for field or shop use

Ridgid 700 Power Drive

Ridgid 700 Power Drive

½" - 2" Conduit using 12-R Die heads.
2½" - 6" conduit using adapter and 141/161

Ridgid 300 Power Drive

Ridgid 300 Power Drive

½" - 2" Conduit with carriage. 2½" - 6" Conduit using adapter and 141/161

Ridgid 141/161 Geared Threader

Ridgid 141/161 Geared Threader

• 141 threads 2-½", 3", 3-½", 4" pipe with one set of dies
• 161 threads 4", 4-½", 5", 6" pipe with one set of dies
• Jaw clutch prevents jamming
• Simple adjustment for tapered or straight threads
• Cam-type workholder sets instantly
• Fully enclosed gearing
• Right-hand only

Ridgid 918 Roll Groover

Ridgid 918 Roll Groover

The RIDGID Model 918 Hydraulic Roll Groover features a powerful 15 ton hydraulic ram in a compact, easy to transport unit. With one man set-up and operation, the 918 is the ideal groover for job-site requirements. The 918 mounts quickly to RIDGID 300 power drive, 535, 1822, or 1224 Threading Machines. Designed to provide maximum efficiency, the 918 is capable of grooving up to 12" Schedule 10 and 8" Schedule 40 standard wall pipes. Roll Set changeout is accomplished in seconds.

12-R Die Heads

12-R Die Heads

½" - 2" Conduit